Brewly

Brewly Large Pump Hose Adaptor for 40L & 70L Brewery. Silicone. Spare part.

Brewly Small Pump Hose Adaptor for 40L & 70L Brewery. Silicone. Spare part.

The Brewly BWH30L is an efficient, compact 2500W semi-automatic brewer with adjustable malt basket for efficient sparging, bazooka bottom filter and tap. You mash, blanch and boil in the same vessel - Cooling coil sold separately. Via the clear digital display, you can easily set the temperature and time. Can also be used as a sparge water kettle.The malt is placed in a malt basket with a perforated insert that can be easily lifted up with the steel handle in two steps for easy leaching after mashing.Internally, there is a volume level gauge set on the stainless steel wall.Brewly BWH30L Brewery- Material: Polished stainless steel (AISI 304)- Brewing volume: 30 liters (max), at least 15L batches are recommended.- Total volume: 35 litres- Digital Controller with clear display - Set temperature and time.- Temperature range 25°C to 100°C, adjustable in steps of 0.1°C.- Temperature control up to 100°C, with +-1°C accuracy.- Power: 2500W in total (adjustable in 700W and 1800W, or both elements at the same time which gives 2500W). 10-16A fuse is recommended. The heating elements are placed under the base to avoid caramelization of the wort and to reduce burning.- Malt basket with steel handle: Can be raised in several steps.- Maximum recommended malt quantity is 8 kg.- Tap with Bazooka mesh-screen filter (raised Mesh-screen bottom filter for efficient separation of hops from the wort)- Strong glass lid- Height: 67 cm- Diameter: 36 cm (without handle and faucet)- Weight: 10 kg (freight carrying weight 40 kg)- Instruction manual- EU-power plug (UK power plug not included)- 220-240V 50/60Hz- Instructions Manual in EnglishMash water calculation:mash water in liters = (amount malt in kilos * 2,5) + 10L.Note: 2,5 is the ratio between water and malt, ie how thick the mash is going to be. This ratio can be varied between approx 2,2-3. 10L is the volume of water below the malt basket inside the brewery.Example: For a 20L recipe with 6kg malt the mash water calculation is as following: 6*2,5+10 = 25L.Sparging: For a 20L recipe, sparge with 78-degree C water up to the 25L mark, and then start the boil (you may start heating the wort while sparging to save time).

Spare part. Brewly Malt Basket Ring for 40L/70L Brewery

Brewly 40L Perforated Malt Basket. New open, perforated design for high wort flow. 304 Stainless steel. Fits Brewly 40L V1 and V2, Höjd: ca 33,5 cmdiameter uppe: ca 37 cmdiameter nere: ca 35 cm

Brewly 70L V2 Perforated Malt Basket. New open, perforated design for high wort flow. 304 Stainless steel. NOTE! Fits only Brewly V2 brewery, not V1 or forst generation 65L & 70L. height: ca 33,5 cmdiameter up: ca 37 cmdiameter down: ca 35 cm

Spare part. Brewly Telescopic Malt Basket Tube 40L.

Spare part. Brewly Telescopic Malt Basket Tube 40L.

For perfectly milled grains, ease of use and superior dependability, look no further than Brewly Malt Mill 3 - A 3-roller grain mill with metal rod base. The Malt Mill 3 achieves the ideal crush for your brewery. It features a fully adjustable roller gap from 0.6mm (0.025") all the way to 2.5mm (0.1”), allowing you to finely tune your crush to your exact preference. Features include SS304 stainless steel rollers, sealed bearings, a 5kg (11lb) capacity grain hopper, an ergonomic crank handle, and unlike other available grain mills, this Malt Mill 3 comes complete with a sturdy metal rod base that fits perfectly on bottling/fermenting buckets. Use either the hand-crank or a power drill with low-RPM and 3/8” chuck.Contains:- Malt Mill with 3 rollers (drive is on one roller, and 2 adjustable rollers.- Grain hopper for up to 5kg (11lb) malt with screws- Solid metal rods for base support- Hand crankSpecifications:- 3-steel rollers: Stainless steel- Grinder housing: Aluminum 6061- Hoppers: Stainless steel- Total height: 280mm- Hopper dimensions at top: 223 x 210mm- Footprint size of grinder: 150 x 88mm- Dimensions: 85 x 150 x 80mm- Steel Rollers: ø 32 x 125mm - Adjustable distance: 0,025 - 0,1 inch (0.635 - 2,54 mm)- Crank handle: 200mmNote: The protective plastic layer can easily be removed.

Brewly DWH30L Digital Water Heater 30L is a digital, double-walled 2500W thermostatically controlled leach water boiler for rapid heating of leach water - HLT (Hot Liquor Tank). With safety cap that needs to be rotated to open. Double walls for extra insulation so the heat is isolated better and the temperature is kept stable for longer. This leach water heater has the exact same ball valve that sits on Brewy's brewhouse, a professional product in stainless steel.Brewly DWH30L Digital Water Heater 30L- Quality construction in stainless steel (ANSI 304)- Double Wall - Double walls for extra insulation so the heat is insulated better and the temperature is kept stable for longer.- 2500W heating element for fast heating, adjustable to 700W, 1800W or 2500W- Built-in heating element under the bottom for easy cleaning- Accurate digital temperature control via knob, +/- 1°C- Thermostat setting 1-100/110°C (110°C for full effect)- Boil-Dry-Protection - Automatic protection in case of overheating- Safety lid that needs to be rotated to open- Stainless ball valve- Heavy duty handles for heavy lifting (do not move with boiling water inside)- Volume up to edge is 30L- 230V (50/60 Hz)

Conical silicone plug stopper for airlock with 9mm hole. Cylindroconical form.Diameter Top: 23 mmDiameter Bottom: 17 mmHeight: 26 mmHole: 9 mm

Silicone plug stopper for airlock with 9mm hole. Cylindroconical form.Diameter Top: 26 mmDiameter Bottom: 19 mmHeight: 28 mmHole: 9 mm

Silicone plug stopper for airlock with 9mm hole. Cylindroconical form.Diameter Top: 29 mmDiameter Bottom: 22 mmHeight: 28 mmHole: 9 mm

Silicone plug stopper for airlock with 9mm hole. Cylindroconical form.Diameter Top: 33 mmDiameter Bottom: 25 mmHeight: 28 mmHole: 9 mm

Silicone plug stopper for airlock with 9mm hole. Cylindroconical form.Diameter Top: 37 mmDiameter Bottom: 28 mmHeight: 30 mmHole: 9 mm

Silicone plug stopper for airlock with 9mm hole. Cylindroconical form.Diameter Top: 45 mmDiameter Bottom: 35 mmHeight: 30 mmHole: 9 mm

Silicone plug stopper for airlock with 9mm hole. Cylindroconical form.Diameter Top: 53 mmDiameter Bottom: 28 mmHeight: ca 32 mmHole: 9 mm

Silicone plug stopper for airlock with 9mm hole. Cylindroconical form.Diameter Top: 56 mmDiameter Bottom: 46 mmHeight: 34 mmHole: 9 mm

Silicone plug stopper for airlock with 9mm hole. Cylindroconical form.Diameter Top: 65 mmDiameter Bottom: 55 mmHeight: 38 mmHole: 9 mm

Pressure ferment your beer at up to 1 bar (15 psi) in stainless conical fermentation tank like in professional breweries! Large container for yeast and yeast dumping of 900 ml. Perfect for batch sizes up to 35L (40L to the brim). Cooling spiral (chiller) and neopren jacket sold seperately.Brewly CPF35L 35L Conical Pressure Fermenter- Material: Polished stainless steel (ANSI 304)- Polished seamless interior for maximum cleanliness- Maximum pressure 1 bar (15 psi) with safety valve- 35L fermentation capacity (40L up to edge)- Thermowell in the lid for temperature sensor (sensor not included).- Ball locks (threaded) in the lid for gas and beer.- Mini-valve 3/8" for sampling etc- 900ml removable container for dumping yeast and trub. Separates from tank with Tri-clamp butterfly valve.- Connections 1/2" for connection of internal cooling coil (sold separately)- Internal volume scale- Strong steel handles- 3 legs with wheels including brake- Stainless lid with strong silicone gasket- Instruction manual- Diameter: 400 mm (not including handles)- Height: 1050 mm (with feet)

Brewly CPF35L Chiller 5,5 meters - Cooling spiral in 304 stainless steel for Brewly CPF35L pressure fermenter. NOTE: Includes only the chiller/cooling spiral, not the other equipment in the picture.

Brewly CPF35L Chiller - Cooling spiral in 304 stainless steel for Brewly CPF35L pressure fermenter. NOTE: Includes only the chiller/cooling spiral, not the other equipment in the picture.

Heat insulation for the Brewly 40L V2 brewery. Provides faster heating, more vigorous boil and reduces energy consumption. Material: 5 mm neoprene foam.NOTE: Made for Brewly V2 40L. Will not fit perfectly on V3.

Brewery 30L with 8,8m chiller. The Brewly BWH30L is an efficient, compact 2500W semi-automatic brewer with adjustable malt basket for efficient sparging, bazooka bottom filter and tap. You mash, blanch and boil in the same vessel - Cooling coil chiller 8,8m included. Via the clear digital display, you can easily set the temperature and time. Can also be used as a sparge water kettle.The malt is placed in a malt basket with a perforated insert that can be easily lifted up with the steel handle in two steps for easy leaching after mashing.Internally, there is a volume level gauge set on the stainless steel wall.Brewly BWH30L Brewery- Material: Polished stainless steel (AISI 304)- Brewing volume: 30 liters (max), at least 20L batches are recommended.- Total volume: 35 litres- Digital Controller with clear display - Set temperature and time.- Temperature range 25°C to 100°C, adjustable in steps of 0.1°C.- Temperature control up to 100°C, with +-1°C accuracy.- Power: 2500W in total (adjustable in 700W and 1800W, or both elements at the same time which gives 2500W). 10-16A fuse is recommended. The heating elements are placed under the base to avoid caramelization of the wort and to reduce burning.- Malt basket with steel handle: Can be raised in several steps.- Maximum recommended malt quantity is 8 kg.- Tap with Bazooka mesh-screen filter (raised Mesh-screen bottom filter for efficient separation of hops from the wort)- Strong glass lid- Height: 67 cm- Diameter: 36 cm (without handle and faucet)- Weight: 10 kg (freight carrying weight 40 kg)- Instruction manual- EU-power plug (UK power plug not included)- 220-240V 50/60Hz- Instructions Manual in EnglishMash water calculation:mash water in liters = (amount malt in kilos * 2,5) + 10L.Note: 2,5 is the ratio between water and malt, ie how thick the mash is going to be. This ratio can be varied between approx 2,2-3. 10L is the volume of water below the malt basket inside the brewery.Example: For a 20L recipe with 6kg malt the mash water calculation is as following: 6*2,5+10 = 25L.Sparging: For a 20L recipe, sparge with 78-degree C water up to the 25L mark, and then start the boil (you may start heating the wort while sparging to save time).

Brewly Stainless Float With Silicone Dip Tube 80cm. Ensure that only the top layer of beer is poured from the fermenter, also fits Fermzilla perfectly. Silikcone tube measurements (dip tube):Inner diameter: 6mm (ID 0.23”)Outer diameter: 8mm (OD 0,35”) Floater diameter: 43mm

The filter prevents hop residue etc from beeing sucked up into a hose, use in kegs, fermenters etc (not with float). Made from HDPE and 304 Grade stainless steel mesh this product can be boiled or sanitized with most detergents.The float can be mounted in three different places on the filter, to determine how close to the surface you want to suck up liquid.Dimensions: 40 x 28 mm. Hose holder diameter: 8 mm, perfect for 6mm inner diameter silicone tube/hose. Materials: Stainless steel 300 mesh and plastic. NOTE: dont use with float as there are no attachments for float on the filter

Fits CO2/Beer Ball-lock-coupling. Sanitize hoses or force carbonate beer on PET Bottle. Also fits FermZilla. Clean your beer line easy. Attach the cap to a soda bottle with cleaning solution. Liquid and Gas ball lock compatible. Stainless steel.Liquid and Gas ball lock compatible. Barbed fitting fits 4mm, 5mm & 6mm ID flexible hoses.

Add this pressure kit to your FermZilla 27L, 35L or 55L and turn your FermZilla into a true uni tank that can be used for carbonating beer. Stainless steel.Brewly Stainless Pressure Kit includes:- 2 x Carbonation Screw Caps with barb- 1 x SS Float & 80cm Silicone Dip TubeThis inexpensive upgrade will truly show you what the FermZilla was designed for. Here are some possibilities:Fermenting Under Pressure:First one of the most intriguing uses is to ferment under pressure which reduces ester production and fusel alcohol production. That means that you can ferment warmer than you normally would, even making lagers at room temperature. Most commercial beer is fermented under pressure just due to the size of commercial tanks and the pressure that is created by the column of beer. It is one of the differences between commercial brewing and homebrewing. The lid has a built in relief valve that will blow at 35psi and we strongly recommend you also purchase an adjustable pressure relief valve, or blow tie kit, that allows you to set a lower pressure. It is also always a good idea to have two relief valves on the FermZilla anytime the unit is under pressure. Carbonating, Pushing, and Serving:When you are fermenting under pressure the beer is already carbonated when you are done fermenting. You can control the level of carbonation by using an adjustable pressure relief. The idea is that the FermZilla can eliminate kegging and you can serve directly from the fermenter. We love this idea but there will probably still be times that you want to keg. Use a beer line to connect the FermZilla to your keg and enjoy the easiest kegging experience ever. You can also choose to send carbonated beer through a beer filter on the way to your keg. When applying pressure with a CO2 tank also make sure that you have a functional relief valve on your CO2 regulator. Lack of OxidationBecause the beer always has a CO2 blanket through fermentation and during any transfers out, oxidation is eliminated. When you cold crash you won't be sucking air back in through an airlock. Key Features:• Ferment beer under pressure to reduce ester and fusel alcohol production• Ability to always draw clear beer with the unique, floating draw tube • Keg already carbonated beer• Use co2 to push beer into a keg or though a filter into a keg• Carbonate and serve beer directly from the FermZilla, eliminating kegging all together.

Brewly 40L Brewery Kit is a affordable kit consisting of Brewly 40L V3 Brewery (with chiller, hop spider, whirlpool & mash paddle) & Brewly 40L Sparge water heater.For specifications, please see the product pages.

Brewly Recirculation Hook Stainless Steel. Perfect for those who want to recirculate in a brewery or other with, for example, an external pump. Fits 10mm and 12mm silicone hose. Stiffer hoses should have 12mm inner diameter to fit. Outer diameter: 12 mmInner diameter 10 mmMaterial: Stainless steel

The Brewly Tap Quick Connect Kit (1/2" BSP/NPT) fits most tap faucets on breweries and sparge water heaters, and is perfect for those who want to recirculate in a brewery or other with, for example, an external pump. Fits 10mm and 12mm silicone hose, max outer diameter 14mm. Stiffer hoses such as PVC need to have an inner diameter of approx. 12mm to fit. Contains:- 1 copper coupling with ball coupling (female) at one end and 1/2" BSP (NPT) coupling at the other- 1 steel coupling with a ball coupling (male) at one end and 1/2" BSP (NPT) threads at the other, which fits, for example, a standard tap faucet (see link below).

Brewly Seals 10-pack for Carbonation Caps & Ball Locks

Brewly Spare Part for Corker Twin Lever. 1pc. NOTE: Corker is not included.

Graduated 15-60L volume tube in polycarbonate that fits the Brewly 70L V1 brewer. Brewly 70L V1 Volume Sight Tube (15-60L)

Brewly Lid in stainless steel for CF 30L Conical Fermenter. Includes Lid, silicone seal, silicone plug for airlock. Spare part.

Brewly Lid in stainless steel for CCF 30L Conical COOLING Fermenter. Includes Lid, silicone seal, silicone plug for airlock. Spare part.

Brewly CPF35L 900ml Collection Container. Spare part.

Brewly Lid in stainless steel for CF 60L Conical Fermenter. Includes Lid, silicone seal, silicone plug for airlock. Spare part.

Brewly Lid in stainless steel for CCF 60L Conical COOLING Fermenter. Includes Lid, silicone seal, silicone plug for airlock. Spare part.

Brewly CPF35L Manometer for Conical Pressure Fermenter 35L. Spare part.

Silicone plug stopper without hole. Cylindroconical form.Diameter Top: 49 mmDiameter Bottom: 38 mmHeight: 30 mm

Silicone plug stopper for airlock with 9mm hole. Cylindroconical form.Diameter Top: 77 mmDiameter Bottom: 64 mmHeight: 41 mmHole: 9 mm

Silicone plug stopper without hole. Cylindroconical form.Diameter Top: 73 mmDiameter Bottom: 60 mmHeight: 38 mm

Silicone plug stopper for airlock with 9mm hole. Cylindroconical form.Diameter Top: 73 mmDiameter Bottom: 60 mmHeight: 38 mmHole: 9 mm

Silicone plug stopper without hole. Cylindroconical form.Diameter Top: 65 mmDiameter Bottom: 53 mmHeight: 38 mm

Silicone plug stopper without hole. Cylindroconical form.Diameter Top: 56 mmDiameter Bottom: 46 mmHeight: 34 mm

Silicone plug stopper without hole. Cylindroconical form.Diameter Top: 45 mmDiameter Bottom: 35 mmHeight: 30 mm

Silicone plug stopper without hole. Cylindroconical form.Diameter Top: 33 mmDiameter Bottom: 25 mmHeight: 28 mm